Black Widow Pro Series Drag Kits assembly 20`19- Same for Promod/Prostock and 10.5
Step 1 - Parts - Carbon fiber Chassis or Black 3mm composite , Qty 4 M3x12mm Flat head screws , Qty 4 M3 Nuts , Qty 2 Black Hex Rear pod lock downs.
Lightly screw in place the 2 rear pod lock downs using supplied hardware from parts list. After step 2 you will than tighten.
Lightly screw in place the 2 rear pod lock downs using supplied hardware from parts list. After step 2 you will than tighten.
|
|
Step 2 - Parts - Left and right rear pods , Qty 2 1/2" flanged bearings , Qty 4 - M3x6mm Pan screws.
Before attaching check pod tab fitment in slots on chassis for desired fit. If you like them looser you can use a flat hobby small file and adjust as needed. Push fit in the 2 flanged bearings flange to outside of each pod side. Than press in motor side right pod into tabs on right side of chassis (Bearing towards rear of chassis) Repeat left side and lightly tighten pods to rear pod lock down using qty 4 M3m6mm pan screws, ones done you can now tighten all screws tight.
Note due to tolerances of +/- thousands of " with CNC machining this step maybe needed -
Before moving onto next step check fitment of axle through both bearings for 2 things, both pods are straight aligned with each other in slot and bearings are not too tight fitted on pods holes for bearings (should be just snug so axle goes in and spins freely both sides) if the bearings are in too tight, axle maybe harder to push through and or not spin as freely. Sanding with paper or using a round file to open bearing hole ever so slightly maybe needed for best axle fitment. Bearing should fit snug but not tight as it will affect axle going through both sides.
|
|
|
Step 3 & 4 - Parts - Qty 5 2" Black knurled cross posts , Qty 4 M3 x 6mm Pan , Qty 4 M3 x 12mm Pan , Qty 4 M3x10mm Pan , Qty 4 M3 rod end links , Qty 2 M3 Titanium turnbuckles & 2 - 3mm spacers.
Assembly your rod ends just a few threads on both turnbuckles, using 2 M3x12mm pan screws attach 1 black knurled cross post top of rear pods towards front (Leaving other rod end free for later attachment). Now install 2 more black knurled posts up top of rear pods towards rear as in picture using 4 M3x6mm Pan screws. Last install final 2 black knurled posts in lower rear section of pods for later install of wheelie bar using 4 M3x10 Pan screw lightly screwed in.
Assembly your rod ends just a few threads on both turnbuckles, using 2 M3x12mm pan screws attach 1 black knurled cross post top of rear pods towards front (Leaving other rod end free for later attachment). Now install 2 more black knurled posts up top of rear pods towards rear as in picture using 4 M3x6mm Pan screws. Last install final 2 black knurled posts in lower rear section of pods for later install of wheelie bar using 4 M3x10 Pan screw lightly screwed in.
|
|
|
Step 5 & 6 - Parts - (Micro servo and servo mounts Not included) can purchase these at amain.com or anywhere online for short servo mounts) carbon fiber top deck and front end upper plate , qty 24 Black 25mm posts deck/front end posts , qty 21 M3x6mm pan screws , qty 25 M3x6mm Flat screws , qty 2 #4 washers .
Assembly - hand tighten all black knurled posts using m3x6mm flat screws for deck plate and front end area. Next install servo mounts (Not included) to deck plate slot (Micro servo will go under deck plate) Using 2 #4 washers to place under screws for servo mounts and allow servo to slide in slot. Line servo gear spline center with deck plate slot.Now install deck plate to posts using 11 M3x6mm pan screws. Install front end plate using 10 M3x6mm pan screws. Final using 2 m3x12mm pan screws to attach other ends of chassis tweak adjust turnbuckle rod end to deck plate. turn rod ends so screw goes in straight through deck plate hole. Adjusting these chassis tweak turnbuckles will come later .
Assembly - hand tighten all black knurled posts using m3x6mm flat screws for deck plate and front end area. Next install servo mounts (Not included) to deck plate slot (Micro servo will go under deck plate) Using 2 #4 washers to place under screws for servo mounts and allow servo to slide in slot. Line servo gear spline center with deck plate slot.Now install deck plate to posts using 11 M3x6mm pan screws. Install front end plate using 10 M3x6mm pan screws. Final using 2 m3x12mm pan screws to attach other ends of chassis tweak adjust turnbuckle rod end to deck plate. turn rod ends so screw goes in straight through deck plate hole. Adjusting these chassis tweak turnbuckles will come later .
Step 7 - Parts - 2 carbon fiber front bumper wings , 4 m3x10mm flat screws . 4 m3 nuts.
Install bumper wings using the supplied hardware above and tighten down. Any up front hole location can be used for body posts (Not Included) Can purchase single body posts as we use at left hander rc search body posts.
Install bumper wings using the supplied hardware above and tighten down. Any up front hole location can be used for body posts (Not Included) Can purchase single body posts as we use at left hander rc search body posts.
Step 8 - Parts - 2 - black steering blocks ,4- 5x11x4 steering block bearings ,4 5x8x2.5 flanged wheel rim bearings , 2 m5x30mm rim axle pan screws (upgrade titanium axles optional) , 2 m5 axle nuts , 4 m3 turnbuckle rod ends , 1 titanium small servo turnbuckle and 1 long titanium steering block to block connection turnbuckle, 2 titanium pivot pins and e-clips 2.5mm , 1 15mm black knurled post ,4 m3x12mm pan screws , 2 m3 nuts , 1 m3x16mm pan screw , 1 m3 3mm spacer. 2 Pen springs or spacers (Not included)
Assembly of front steering - install e-clips to 1 side of each pivot pins , now slide pivot pin up under front end lower a-arm (Now is the time to cut your pen springs or use spacers (small ID springs which can found at ace hardware) to size based ride height you desire.
If using standard 2" skinny drag rims place steering hub all way up and spring under it or spacers. If using traxxas weld wheel rims add shims (not included to get desired ride height) once ride height is set you want attach top e-clip. Next if using 5mm bolt as axle using PTFE washers you can have head side facing on outer rim side ( If using titanium axles OPTIONAL) use PTFE traxxas washers and slide 1 PTFE washer over axle than slide rim on, next slide another PTFE spacer on axle and slide axle into steering block. Nut to inside of chassis. Use 6 PTFE spacers than put nut and tighten. NOTE- dont over tighten using PTFE spacers so little at time to remove side to side movement and so wheel spins freely.
Having this bearing placed over m5 screw is for 2" drag skinny rims but if you got the upgrde titanium axles its not included . If using traxxas weld wheels is used on m5 screw so screw length is enough for those rims. 2 5x8x2.5 flanged wheel bearings go over m5 axle screw and m5 nut.
Twist on all 4 rod ends to both long and short turnbuckles , using the supplied black knurled 15mm post ,1 m3x12mm pan screw and long turnbuckle.Slide steering long turnbuckle through chassis under deck plate and install screw through rod end and under through steering block hole and thread black knurled post on top of steering block as seen in picture. For opposite side use 1 m3x16mm pan screw, 3mm spacer and m3 nut and tighten down. (You will adjust toe later)
Assembly of front steering - install e-clips to 1 side of each pivot pins , now slide pivot pin up under front end lower a-arm (Now is the time to cut your pen springs or use spacers (small ID springs which can found at ace hardware) to size based ride height you desire.
If using standard 2" skinny drag rims place steering hub all way up and spring under it or spacers. If using traxxas weld wheel rims add shims (not included to get desired ride height) once ride height is set you want attach top e-clip. Next if using 5mm bolt as axle using PTFE washers you can have head side facing on outer rim side ( If using titanium axles OPTIONAL) use PTFE traxxas washers and slide 1 PTFE washer over axle than slide rim on, next slide another PTFE spacer on axle and slide axle into steering block. Nut to inside of chassis. Use 6 PTFE spacers than put nut and tighten. NOTE- dont over tighten using PTFE spacers so little at time to remove side to side movement and so wheel spins freely.
Having this bearing placed over m5 screw is for 2" drag skinny rims but if you got the upgrde titanium axles its not included . If using traxxas weld wheels is used on m5 screw so screw length is enough for those rims. 2 5x8x2.5 flanged wheel bearings go over m5 axle screw and m5 nut.
Twist on all 4 rod ends to both long and short turnbuckles , using the supplied black knurled 15mm post ,1 m3x12mm pan screw and long turnbuckle.Slide steering long turnbuckle through chassis under deck plate and install screw through rod end and under through steering block hole and thread black knurled post on top of steering block as seen in picture. For opposite side use 1 m3x16mm pan screw, 3mm spacer and m3 nut and tighten down. (You will adjust toe later)
Step 9 - Parts - carbon fiber ladder bar or flat bar depends on option your choose upon purchase- , Ladder bar parts - 2 ladder side rails , 1 deck plate(no longer included) , 2 m3x16mm pan screws , 2 m3 nuts ,6 m3x6mm pan screws ,2 wheels and 3 black cross posts.
Assembly of ladder bar and install - Using black bushings press into 1/2" bearings all way in till seats flat.Now install on last side rail hole in carbon fiber of wheelie bar. See 4th picture to see your placing on correct side of each rail (side rail adjust slot faces down) Using 2 m3x16mm pan screws and m3 nuts install wheels onto side rails.
Next check deck plate tab slots for semi loose insert and shift movement. If too tight using flat hobby file open tab slots as desired. You want deck plate to be able to shift forward or back on each rail with just slight effort not super loose.
Using the 6 m3x6mm pan screws attach all 3 black knurled posts to one side rail. Once done insert deck plate into slot tabs and do same for opposite side LEAVING the 6 m3x6mm screw loose. Here youll want to adjust deck plate so both your side rails are equal. Tip - picture 3 shows were you can view deck plate and last cross post to see if equal. Once equal you can now install ladder bar to rear pods using the 4 screws we place loose in pods in step 3 & 4. Once those 4 screws are in and tight you can now tighten the final 6 screws of side rails.
Assembly of ladder bar and install - Using black bushings press into 1/2" bearings all way in till seats flat.Now install on last side rail hole in carbon fiber of wheelie bar. See 4th picture to see your placing on correct side of each rail (side rail adjust slot faces down) Using 2 m3x16mm pan screws and m3 nuts install wheels onto side rails.
Next check deck plate tab slots for semi loose insert and shift movement. If too tight using flat hobby file open tab slots as desired. You want deck plate to be able to shift forward or back on each rail with just slight effort not super loose.
Using the 6 m3x6mm pan screws attach all 3 black knurled posts to one side rail. Once done insert deck plate into slot tabs and do same for opposite side LEAVING the 6 m3x6mm screw loose. Here youll want to adjust deck plate so both your side rails are equal. Tip - picture 3 shows were you can view deck plate and last cross post to see if equal. Once equal you can now install ladder bar to rear pods using the 4 screws we place loose in pods in step 3 & 4. Once those 4 screws are in and tight you can now tighten the final 6 screws of side rails.
Step 10 - Parts - rear axle , 2 5/32 axle spacers ,2 4-40 1/4" spur gear pan screws, 8 4-40 cap 3/8" screws, set of 3/4" drag clamp hubs (Spur gear not included) we offer 96t and 99t 48p composite spurs.
Rear axle assembly - Holding both side rear axle bearings in pods slide axle through both bearings so you have close to equal length coming out both sides .Due to cold and heat axle can expand and contract so may feel tighter or looser upon install going through bearings. Now slide a 5/32 spacer onto each side.
Spur gear install on one hub using the supplied 4-40 pan 1/4" screws attach spur gear to hub as shown in picture.
Now your ready to slide your both hubs on same time. Its easier to already have your rims attached in doing so.
youll want to grab both rims and slide them onto axle all the way in to spacers but not tight just lightly snug against spacers. Look at side of each hub you'll see how far axle comes out,Here you can shift axle in or out so you have equal parts sticking out of hub you can measure or eye ball.
Tightening clamp hubs onto axle, theirs 2 screws on each hub youll want to lightly tighten all of them first holding hubs against spacers. Once snug check wheel spin to be free and NO side to side end play, once good tighten fully and equally on all 4 screws.
Tip - Grab both rims with your hands and try to spin them opposite directions if they move tighten more. If one wheel spins this will cause spin out at launch. scuffing axle ends help grab hubs to axle also if needed.
Tip - (Foam tires must be trued to exact height don't assume what you buy or get is exact use dial caliper to measure)To adjust tweak using wheels bar at center lift point lift car slowly up than back down and watch if both rear wheels touch same time if they don't adjust tweak rods till both hit equal and solid on flat surface.
Here are few places and suggestions types to use for body posts and ways to mount like clips or magnets. Some may require trimming down.
www.amazon.com/dp/B007TTVN2E/ref=cm_sw_r_fm_apa_i_LFoYCbZKGJHTA?fbclid=IwAR0PEO8MmrkEfhZ6EwXICdpbHMlNG6MezL5eIHg7_wGXttCb-L-eB4NR4DQ
www.amazon.com/dp/B0147Z9V9E/ref=pd_luc_rh_sspa_dk_huc_pt_expsub_2?psc=1
www.lefthander-rc.com/catalog/advanced_search_result.php?keywords=body+posts
Enjoy your new kit. As always were here for any help you may need or questions.
Thank You
Rear axle assembly - Holding both side rear axle bearings in pods slide axle through both bearings so you have close to equal length coming out both sides .Due to cold and heat axle can expand and contract so may feel tighter or looser upon install going through bearings. Now slide a 5/32 spacer onto each side.
Spur gear install on one hub using the supplied 4-40 pan 1/4" screws attach spur gear to hub as shown in picture.
Now your ready to slide your both hubs on same time. Its easier to already have your rims attached in doing so.
youll want to grab both rims and slide them onto axle all the way in to spacers but not tight just lightly snug against spacers. Look at side of each hub you'll see how far axle comes out,Here you can shift axle in or out so you have equal parts sticking out of hub you can measure or eye ball.
Tightening clamp hubs onto axle, theirs 2 screws on each hub youll want to lightly tighten all of them first holding hubs against spacers. Once snug check wheel spin to be free and NO side to side end play, once good tighten fully and equally on all 4 screws.
Tip - Grab both rims with your hands and try to spin them opposite directions if they move tighten more. If one wheel spins this will cause spin out at launch. scuffing axle ends help grab hubs to axle also if needed.
Tip - (Foam tires must be trued to exact height don't assume what you buy or get is exact use dial caliper to measure)To adjust tweak using wheels bar at center lift point lift car slowly up than back down and watch if both rear wheels touch same time if they don't adjust tweak rods till both hit equal and solid on flat surface.
Here are few places and suggestions types to use for body posts and ways to mount like clips or magnets. Some may require trimming down.
www.amazon.com/dp/B007TTVN2E/ref=cm_sw_r_fm_apa_i_LFoYCbZKGJHTA?fbclid=IwAR0PEO8MmrkEfhZ6EwXICdpbHMlNG6MezL5eIHg7_wGXttCb-L-eB4NR4DQ
www.amazon.com/dp/B0147Z9V9E/ref=pd_luc_rh_sspa_dk_huc_pt_expsub_2?psc=1
www.lefthander-rc.com/catalog/advanced_search_result.php?keywords=body+posts
Enjoy your new kit. As always were here for any help you may need or questions.
Thank You
Traxxas Slash/Rustler 2019 "Pro Street Eliminator" Kit Assembly
Changes in design or parts included may differ with new versions.
These instructions are for basic assembly ONLY
Step 1 - Parts - Bag1 - Lower Chassis, and Y plate
11 - 25mm Posts , 1 - 15mm post , 11 m3x6mm pan screws ,12 m3x6mm flat screws ,
Install posts using all the m3x6mm flat screws. Install Y plate using m3x6mm pan screw BUT leave screw loose for later tightening. Anodized aluminum Post style type may vary from knurled to smooth etc based on availability of manufacture of posts
in china. At this time red posts are not available. Those who ordered red before this back order will be noted to ship red posts when back in in meantime black is sent with kits.
11 - 25mm Posts , 1 - 15mm post , 11 m3x6mm pan screws ,12 m3x6mm flat screws ,
Install posts using all the m3x6mm flat screws. Install Y plate using m3x6mm pan screw BUT leave screw loose for later tightening. Anodized aluminum Post style type may vary from knurled to smooth etc based on availability of manufacture of posts
in china. At this time red posts are not available. Those who ordered red before this back order will be noted to ship red posts when back in in meantime black is sent with kits.
Step 2 - Parts - Bag 2
2- m3x16 pan screws ,2 - 4mm spacers ,2 -M5 x 40mm flat screws,2 - m5x35 flat screws , 2- m5 nuts , NS link , 2 -m3x6mm x 2.5mm bearings, 2 -5x8.2.5 bearings. 1 - m3x10 pan , 1 - m3 x 12 pan and 1 - m3 nut , 2 - m4x25mm flat ,2-m4x30 flat , 2 - m4 nuts,12 -5mmx-0.5mm shims, 4- #4 washers
Install your servo and mounts of choice ( Not included ) Press bearings into NS link for bell crank (May come already pressed). Install bell crank using the m5 x 40mm flat head bolts/nuts and 2 5x8x2.5 bearings. Place 2 5x8x2.5 bearings above bell crank.*Depending on Bell crank used shimming maybe required using 5mm ID shims with 12 included.More or less maybe needed.
Take the 2 m3x16mm pan screws and 2 4mm spacers and use to attach turnbuckle link to bell crank later on. (NOT INCLUDED ) Screw on 3mm rod end links to M3 ,45mm Long turnbuckle and attach to servo arm and bell crank using provided m3x10mm
(attaches turnbuckle to bell crank & M3x16 pan screw and nut attaches turnbuckle to servo arm)
Depending on brand of bell crank used screws provided to attach titanium servo turnbuckle may need to be longer or shorter. Provided are screws for HR aluminum bell crankswww.amazon.com/Hot-Racing-Aluminum-Bellcranks-Draglink/dp/B00XF8KTZA/ref=sr_1_1?keywords=hot%20racing%20traxxas%20slash%20bellcrank&qid=1559247321&s=gateway&sr=8-1-spell&fbclid=IwAR3O8QjNJEBs5QwRG86QjcRW53HHNoSN7vE_DLlOFzw8f9-xlULpfHBxNsU.
Fine tune adjust servo adjustment at any point in steps now or at end.
2- m3x16 pan screws ,2 - 4mm spacers ,2 -M5 x 40mm flat screws,2 - m5x35 flat screws , 2- m5 nuts , NS link , 2 -m3x6mm x 2.5mm bearings, 2 -5x8.2.5 bearings. 1 - m3x10 pan , 1 - m3 x 12 pan and 1 - m3 nut , 2 - m4x25mm flat ,2-m4x30 flat , 2 - m4 nuts,12 -5mmx-0.5mm shims, 4- #4 washers
Install your servo and mounts of choice ( Not included ) Press bearings into NS link for bell crank (May come already pressed). Install bell crank using the m5 x 40mm flat head bolts/nuts and 2 5x8x2.5 bearings. Place 2 5x8x2.5 bearings above bell crank.*Depending on Bell crank used shimming maybe required using 5mm ID shims with 12 included.More or less maybe needed.
Take the 2 m3x16mm pan screws and 2 4mm spacers and use to attach turnbuckle link to bell crank later on. (NOT INCLUDED ) Screw on 3mm rod end links to M3 ,45mm Long turnbuckle and attach to servo arm and bell crank using provided m3x10mm
(attaches turnbuckle to bell crank & M3x16 pan screw and nut attaches turnbuckle to servo arm)
Depending on brand of bell crank used screws provided to attach titanium servo turnbuckle may need to be longer or shorter. Provided are screws for HR aluminum bell crankswww.amazon.com/Hot-Racing-Aluminum-Bellcranks-Draglink/dp/B00XF8KTZA/ref=sr_1_1?keywords=hot%20racing%20traxxas%20slash%20bellcrank&qid=1559247321&s=gateway&sr=8-1-spell&fbclid=IwAR3O8QjNJEBs5QwRG86QjcRW53HHNoSN7vE_DLlOFzw8f9-xlULpfHBxNsU.
Fine tune adjust servo adjustment at any point in steps now or at end.
Step 3 - Parts - Bag 3 -(Optional) if you purchased the carbon fiber or Delrin front tower. 2 - m4x10mm flat screws , 2 - 2 -8mm spacers. Option includes -front shock tower,2-m3x10 pan screws, 2 - m3x30mm pan screws , 4-m3 nuts, 2 - m3x20mm
Installing front shock tower on your traxxas bulk head/front end assembly (Not included)
Using the 2 - m3x10mm attach shock tower to bulkhead as shown. (Front end is installed flipped around verse how its is for stock slash for a more street suspension not angled for off road)
Next using the 2 - m3x30mm pan screws 2-nuts and 2- 12mm spacers install as shown in picture for turnbuckle linkage.
Remaining 2 - m3x20mm pan and nuts are for attaching shocks to tower.
Now attach your front end onto chassis using the 2 - m4x10 flat screws towards the front and 2 - m4x25mm flat screws towards the rear as these go through the Y plate and attach with the m4 nuts and 12mm spacers below y plate.
Shocks used are traxxas 4tec shocks.
Installing front shock tower on your traxxas bulk head/front end assembly (Not included)
Using the 2 - m3x10mm attach shock tower to bulkhead as shown. (Front end is installed flipped around verse how its is for stock slash for a more street suspension not angled for off road)
Next using the 2 - m3x30mm pan screws 2-nuts and 2- 12mm spacers install as shown in picture for turnbuckle linkage.
Remaining 2 - m3x20mm pan and nuts are for attaching shocks to tower.
Now attach your front end onto chassis using the 2 - m4x10 flat screws towards the front and 2 - m4x25mm flat screws towards the rear as these go through the Y plate and attach with the m4 nuts and 12mm spacers below y plate.
Shocks used are traxxas 4tec shocks.
Step 4 - Parts - Bag 4 -
Upper Deck plate (New style with upper deck has deck servo mounting or lower chassis servo mounting) , 2 - m3x16 pan , 2 - m3 x 12 pan screws,2 - m3 nuts, 9 - m3x6mm pan screws , 2 - 3mm spacers.
Install upper deck plate to chassis using the 9 m3x6mm screws , Next install front mount plate to upper deck plate using m3x6mm pan screws, 2 - m5 nuts left over from step 2. Leave 2 upper deck plate holes open for turnbuckles which use 2 - m3x16 pan screws/spacers.
Next assembly the 3mm rod end links onto the turnbuckles (Final length/adjustment is done at end) and set aside.
Upper Deck plate (New style with upper deck has deck servo mounting or lower chassis servo mounting) , 2 - m3x16 pan , 2 - m3 x 12 pan screws,2 - m3 nuts, 9 - m3x6mm pan screws , 2 - 3mm spacers.
Install upper deck plate to chassis using the 9 m3x6mm screws , Next install front mount plate to upper deck plate using m3x6mm pan screws, 2 - m5 nuts left over from step 2. Leave 2 upper deck plate holes open for turnbuckles which use 2 - m3x16 pan screws/spacers.
Next assembly the 3mm rod end links onto the turnbuckles (Final length/adjustment is done at end) and set aside.
Step 5 - Parts - Bag 5 -Rear low profile shock tower , Shock tower mount plate (Street eliminator specific) 2 - m3x12mm pan screws , 8- m3 nuts , 2 - m3x12mm flat screws , 4 - m3x20mm pan , 2 - m3x16mm pan screws, 2 - m3x10 pan and 4 - m4x10mm flat.
(Note rear 2 transmission 3mm holes have been removed from design only use 4- m4x10mm flat screws)
Using the 2 - m3x12 flat screws and nuts attach mount plate to tower as pictured. (NOT INCLUDED -45mm long 3mm needed x 2 and 4 -3mm rod ends -Turnbuckle center to center adjustment may vary on kits as a before the revised version used shorter turnbuckles) Screw rod ends onto turnbuckles and adjust to 58mm center hole to hole to start.
Next using the m3x12 pan screw attach turnbuckles to tower plate using the 2 - m3x10 pan screws and nuts and using screws from bag 4 attach turnbuckles using the 2 - m3x16 pan screws and 3mm spacers under turnbuckle between deck plate . Now install tower assembly to gear box. Adjusting turnbuckle maybe required to get alignment for deck plate screws. Final adjustment done at end.
Using the 4 - m4x10mm fat screws attach your traxxas rear assembly to chassis kit.
The remaining 16mm and 20mm screws are for your traxxas turnbuckles to attach to tower.
Traxxas rear shock used for our low profile tower are traxxas slash fronts or traxxas bandit rears which is same part number.
(Note rear 2 transmission 3mm holes have been removed from design only use 4- m4x10mm flat screws)
Using the 2 - m3x12 flat screws and nuts attach mount plate to tower as pictured. (NOT INCLUDED -45mm long 3mm needed x 2 and 4 -3mm rod ends -Turnbuckle center to center adjustment may vary on kits as a before the revised version used shorter turnbuckles) Screw rod ends onto turnbuckles and adjust to 58mm center hole to hole to start.
Next using the m3x12 pan screw attach turnbuckles to tower plate using the 2 - m3x10 pan screws and nuts and using screws from bag 4 attach turnbuckles using the 2 - m3x16 pan screws and 3mm spacers under turnbuckle between deck plate . Now install tower assembly to gear box. Adjusting turnbuckle maybe required to get alignment for deck plate screws. Final adjustment done at end.
Using the 4 - m4x10mm fat screws attach your traxxas rear assembly to chassis kit.
The remaining 16mm and 20mm screws are for your traxxas turnbuckles to attach to tower.
Traxxas rear shock used for our low profile tower are traxxas slash fronts or traxxas bandit rears which is same part number.
Step 6 - Parts - Bag 6 - Wheelie bar option choice and HR extended motor mount plate
If choosing the ladder bar option for mounting to RPM or STL rear bumper mount - parts include - 2 - side rails , 1 - center deck plate , 4 - cross posts , 6 - m3 x 1/4" pan screws , 2 - m3x16 pan screws , 2 - m3 nuts , 2 - 5/8" dia wheels , 2 - plastic wheel bushings and 4 - m3x10mm mounting screws. if bolting to a Hot Racing transmission your mounting posts and hardware come with that transmission.
Install of ladder bar - attach all 3 black aluminum cross bars to one side of side rail. Next place deck plate into slots and attach other side rail all using 6 - m3 x 1/4" pan screws. Next install wheels - push bushings all way into wheels, than using M3X16mm pan screws and nuts attach to last hole on side rails with 4th post. If bolting to traxxas any gear box other than Hot Racing must use RPM or STL rear bumper mount and 4 supplies m3x10mm pan screws.
If you choose a 2019 flat wheelie bars - Parts are - 3mm wheelie bar , wheelie bar mount plate , 4 - 4-40 3/8 pan screws , 5 - 4-40 nuts , 1 axle bolt and 1 - 3/4" dia rubber wheel with aluminum hub.
(Adjusting turnbuckle not included) Install to bottom chassis gear box screws using the 4 - m4x10mm flat screws.
Hot racing extended gearing motor plate as far as we know will only bolt to Hot racing transmissions as it was designed for. Bolts on just like original plate using existing hardware.
Pictures or whats shown in pictures may vary due to near changes in design, features or options. Ask if not sure or refer to description for full info.
If choosing the ladder bar option for mounting to RPM or STL rear bumper mount - parts include - 2 - side rails , 1 - center deck plate , 4 - cross posts , 6 - m3 x 1/4" pan screws , 2 - m3x16 pan screws , 2 - m3 nuts , 2 - 5/8" dia wheels , 2 - plastic wheel bushings and 4 - m3x10mm mounting screws. if bolting to a Hot Racing transmission your mounting posts and hardware come with that transmission.
Install of ladder bar - attach all 3 black aluminum cross bars to one side of side rail. Next place deck plate into slots and attach other side rail all using 6 - m3 x 1/4" pan screws. Next install wheels - push bushings all way into wheels, than using M3X16mm pan screws and nuts attach to last hole on side rails with 4th post. If bolting to traxxas any gear box other than Hot Racing must use RPM or STL rear bumper mount and 4 supplies m3x10mm pan screws.
If you choose a 2019 flat wheelie bars - Parts are - 3mm wheelie bar , wheelie bar mount plate , 4 - 4-40 3/8 pan screws , 5 - 4-40 nuts , 1 axle bolt and 1 - 3/4" dia rubber wheel with aluminum hub.
(Adjusting turnbuckle not included) Install to bottom chassis gear box screws using the 4 - m4x10mm flat screws.
Hot racing extended gearing motor plate as far as we know will only bolt to Hot racing transmissions as it was designed for. Bolts on just like original plate using existing hardware.
Pictures or whats shown in pictures may vary due to near changes in design, features or options. Ask if not sure or refer to description for full info.
Enjoy your new kit. As always were here for any help you may need or questions.
Thank You
Thank You
Traxxas Street Eliminator Kit 2.5
3mm chassis plate
3mm esc plate
3mm side rails
2 - red anodized esc posts
12 - red anodized side rails posts
2 - 20mm M4 bolts for front bulk head
2- 25mm M4 bolts for front bulk head
2 - M4 nuts
14 - M3x6mm Pan screws
2 - m3x10mm pan screws
14 M3x6mm Flat chassis screws
3mm chassis plate
3mm esc plate
3mm side rails
2 - red anodized esc posts
12 - red anodized side rails posts
2 - 20mm M4 bolts for front bulk head
2- 25mm M4 bolts for front bulk head
2 - M4 nuts
14 - M3x6mm Pan screws
2 - m3x10mm pan screws
14 M3x6mm Flat chassis screws
Team Associated B6 street eliminator kit
SE-7 & XD-7 Base kit Parts list -
Qty 1 - 13.25" 3mm Chassis , 3mm Front brace plate , shorty Battery plate, 1 - 8mm post , 18 -8mm flat head screws , 12- 3mm nuts , 7 - 8mm pan head,2 -6mm flat head screws, 1 - 16mm pan screws,1 - 3mm spacer , 4 -38mm posts and 4 - 8mm posts
New Updated version may differ in pictures with or without some parts shown in pictures.
Required parts - B6 kit or parts car , servo, servo mounts , electronics , body, wheels/tires
Att: front bulkhead upper deck plate required to be cut off. Car poses a upright front suspension for drag racing (See images below)
Optional Parts - 9" Wheelie bar , slim line front bumper & Wide rear shock tower
Qty 1 - 13.25" 3mm Chassis , 3mm Front brace plate , shorty Battery plate, 1 - 8mm post , 18 -8mm flat head screws , 12- 3mm nuts , 7 - 8mm pan head,2 -6mm flat head screws, 1 - 16mm pan screws,1 - 3mm spacer , 4 -38mm posts and 4 - 8mm posts
New Updated version may differ in pictures with or without some parts shown in pictures.
Required parts - B6 kit or parts car , servo, servo mounts , electronics , body, wheels/tires
Att: front bulkhead upper deck plate required to be cut off. Car poses a upright front suspension for drag racing (See images below)
Optional Parts - 9" Wheelie bar , slim line front bumper & Wide rear shock tower
|
|
|
|
|
|
|
|